Wavetek 39A Spécifications Page 95

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 137
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 94
User Manual 301/302
SOURce
Subsystem
This subsystem is used to control output functions, shape and
parameters, frequency, amplitude and amplitude modulation, and filter
type. Optional nodes were omitted from these commands. Factory
defaults after *RST are shown in bold typeface. Parameter low and
high limits are given where applicable.
Keyword Parameter Form Default,Low Limit,High Limit
[:SOURce]
:AM (?) {OFF|ON|0|1} OFF
:APPLy (?)
:SINusoid (?) {<freq>,<ampl>,<offs>,<phase>}
:TRIangle (?) {<freq>,<ampl>,<offs>,<phase>}
:SQUare (?) {<freq>,<ampl>,<offs>,<duty_cycle>}
:PULSe (?) {<freq>,<ampl>,<offs>,<delay>,<rise>,<high>,<fall>}
:RAMP (?) {<freq>,<ampl>,<offs>,<delay>,<rise>,<fall>}
:SINC (?) {<freq>,<ampl>,<offs>,<N_cycles>}
:EXPonential (?) {<freq>,<ampl>,<offs>,<exp>}
:GAUSsian (?) {<freq>,<ampl>,<offs>,<exp>}
:DC (?) {<%_ampl>}
:USER (?) {<seg#>,<sclk>,<ampl>,<offs>}
:FREQuency (?) {<freq>|MINimum|MAXimum} 1e6,100e-6,150e6
:RASTer (?) {<sclk>|MINimum|MAXimum} 10e6,100e-3,300e6
:SOURce (?) {EXTernal|INTernal} INTernal
:FUNCTion
:MODE (?) {FIXed|USER|SEQuence} FIXed
:SHAPe (?) {SINusoid|TRIangle|SQUare|PULSe|
RAMP|SINC|EXPonential|GAUSsian|DC} SINusoid
:PHASe:STEP (?) {POINt|DEGRee} POINt
:OFFSet (?) <course_offs> 0,0,n
:FINE (?) <fine_offs> 0,0,131072
:VOLTage (?) {<ampl>|MINimum|MAXimum} 2,10e-3,5
:OFFSet (?) <offs> 0,-2.5,2.5
:SINusoid
:PHASe (?) <phase> 0,0,360
:TRIangle
:PHASe (?) <phase> 0,0,360
:SQUare
:DCYCle (?) <duty_cycle> 50,1,99
:PULSe
:DELay (?) <delay> 10,0,99.9
:WIDTh (?) <pulse_width> 10,0,99.9
:TRANsition (?) <rise> 10,0,99.9
:TRAiling (?) <fall> 10,0,99.9
:RAMP
:DELay (?) <delay> 0,0,99.9
:TRANsition (?) <rise> 60,0,99.9
:TRAiling (?) <fall> 30,0,99.9
:SINC
:NCYCle (?) N_cycles> 10,4,100
:GAUSsian
:EXPonent (?) <exp> 20,10,200
:EXPonential
:EXPonent (?) <exp> -20,-100,+100
SCPI Command Reference
84
Vue de la page 94
1 2 ... 90 91 92 93 94 95 96 97 98 99 100 ... 136 137

Commentaires sur ces manuels

Pas de commentaire