¤TMDigital Multimeter/Multi TesterOperator’s ManualModel DM2Digital Multimeter• Manual de InstruccionesDM2.Man.08.00 11/29/00 8:28 PM Page 2
– 9 –4. Inspect and test the fuse. If it is necessary to replace the fuse, be sureto install on of the proper current value. (See fuse replacementbe
– 10 –purchase (warranty repairs), a brief description of the problem or theservice requested, and the appropriate service charge (for non-war-ranty r
¤TMDigital Multimeter/Multi TesterManual de InstruccionesModel DM2Digital MultimeterDM2.Man.08.00 11/29/00 8:28 PM Page 11
– 12 –GARANTÍAEl multímetro DM2 está garantizado contra cualquier defecto de mate-rial o de mano de obra durante un periodo de un (1) año contado apar
– 13 –ADVERTENCIAS Y PRECAUCIONES No debe utilizarse este instrumento sobre hilos sin aislar a ten-siones superiores a 500 V CA o 1000 V DC. No su
– 14 –FUNCIONAMIENTO DEL MEDIDORSelección de la EscalaSi no conoce la mangitud de la escala que van a medir, selecione enel primer lugar la escala más
– 15 –MEDIDAS DE TENSION CC Y CA (DCV Y ACV)1. Antes de conectar o desconectar las puntas de prueba a/de un cir-cuito, simpre apague el dispositivo o
– 16 –4. Conecte la punta de prueba roja a Ω conectela a otra punta del resis-tor5. Ajuste la función/escala que le da la lectura más precisaNota: Par
– 17 –ESPECIFICATIONESEspecificationes GeneralesVisualizador: LCD de 31/2 digitos, 1999 cuentasIndicación de polaridad: automatica, positiva implicada
– 18 –Voltos CAEscalas: 200V, 500VPrecisión: ±1.2%de la lectura, +10 digitosProtección subrecarga: 500VCA RMS/500VCCCorriente CCEscalas: 200mA, 2mA, 2
– 1 –WARRANTYThe DM2 Multimeter is warranted against any defects of material orworkmanship within a period of one (1) year following the date of pur-c
– 19 –MANTENIMIENTOADVERTENCIAPara evitar el peligro de descarga electrica, apague el multímetro ydesconecte las puntas de prueba antes de abrir la t
– 20 –REPARACIÓNLea las condiciones de grantía, al principio de este manual, antes desolicitar cualquier reparación dentro o fuera de garantía. Si la
Manual Revision 08/00Manual Part Number 1566172Information contained in thismanual is proprietary to WavetekMeterman and is provided solelyfor instrum
SYMBOLSDirect currentAlternating currentGround connectionAttention! Refer to Operating InstructionsDangerous voltage may be present at terminalsWARNIN
– 3 –ACCESSORIESVC12 Vinyl Carring CaseRTL25 Replacement Test LeadsUNPACKING AND INSPECTIONUpon removing your new digital multimeter (DM2) from its pa
– 4 –the overload condition from the meter. Select the next higher rangeuntil a value is displayed. If overload condition still exists in thehighest
– 5 –VOLTAGE MEASUREMENT1.Turn off power to the device under test and discharge all capacitors.2.Set the Function/Range switch to the desired voltage
– 6 –RESISTANCE MEASUREMENTS1.Turn off any power to the resistance to be measured. Discharge anycapacitors. Any voltage present during a resistance
– 7 –Bipolar transistor junctions may be tested in the same manner describedabove as emitter-base and base-collector junctions are diode junc-tions.SP
– 8 –AC VoltsRanges: 200V, 500VAccuracy: 1.2% RDG + 10 DigitsOL Protection: 500VAC RMS/500VDCDC CurrentRanges: 200 A, 2mA, 20mA, 200mAResolution: 100n
Commentaires sur ces manuels